(866) 99-PUMPS
78677
(626) 480-7747
banner
Booster Pumps
Filter By
   
These AMT commercial/industrial centrifugal pumps are non-self-priming (gravity feed) units designed to handle high-pressure low flow liquid transfer applications where no suction lift is required. Typical installations include hot and chilled water, boiler feed, condensate return, irrigation, high pressure wash-down, booster service, and fire protection/sprinkler systems—often referred to as a Jockey Pump. These pumps have NOT been investigated for use in potable (drinking) water systems.
AMT MSV1
sd
These AMT commercial/industrial centrifugal pumps are non-self-priming (gravity feed) units designed to handle high-pressure low flow liquid transfer applications where no suction lift is required. Typical installations include hot and chilled water, boiler feed, condensate return, irrigation, high pressure wash-down, booster service, and fire protection/sprinkler systems—often referred to as a Jockey Pump. These pumps have NOT been investigated for use in potable (drinking) water systems.
AMT MSV3
sd
The AquaBoost 2 (AB2) variable speed pump controller and complete booster package kits, provide an economical answer for municipal water district customers with low water pressure. Both domestic and light commercial applications can benefit. As water use increases, the controller changes pump speed to maintain pressure. Large supply tanks are eliminated and less wear and tear on your pump and motor.
Goulds AquaBoost II
sd
The e-HM is available in two different configurations: “Compact” design - for sizes 1HM, 3HM, and 5HM up to a maximum of 6 stages. “Sleeve” design - for sizes 1HM, 3HM and 5HM starting at 7 stages and above;and all sizes of 10HM, 15HM, and 22HM sizes. Motor The e-HM series incorporates a Lowara IEC premium efficiency (IE3), inverter design motor for additional energy savings, and versatility. The standard motor enclosure is a TEFC (IP55) design.
Goulds e-HM Series
sd
Horizontal and vertical configuration high pressure pumps for water boost applications in both surface and tank mount environments. Stainless steel or cast iron construction with variable suction and discharge orientation. Flows to 350 GPM and 800 feet TDH. Designed to handle a wide range of filtration, pressure boost, wash system and boiler feed applications.
» 1 e-SV
» 3 e-SV
» 5 e-SV
Goulds e-SV Vertical Multi-Stage Pumps
sd
The basic CR pump range is available in four different materials including cast iron (CR), two grades of stainless steel (CRI / CRN), and all-titanium versions (CRT) in eleven flow sizes, capable of producing almost 50 bars of pressure, and with a variety of shaft seals, rubbers, and supply voltages.
» CR 1
» CR 10
» CR 120
» CR 15
» CR 150
» CR 1s
» CR 20
» CR 3
» CR 32
» CR 5
» CR 64
» CR 90
Grundfos CR / CRI / CRN / CRT Pumps
sd
The MVI is the pressure-boosting workhorse of the WILO lineup, and is applicable in a variety of municipal, industrial, process, commercial and HVAC applications ranging from pressure boosting and water supply, to washing systems and boiler feed. Featuring built-in air venting and priming plugs, standard Baldor NEMA frame motors, an extra thrust bearing in the pump end, and an excellent commercial pump warranty, the MVI stays well ahead of the pack. Wilo-Multivert MVI 10,15,30,50 and 80
» MVI 10
» MVI 15
» MVI 30
» MVI 50
Wilo MVI Pumps
sd
The WILO MVIS is the only pressure booster pump with maintenance-free wet rotor technology in the world! The MVIS features a maximum noise output of 40db, stainless steel construction for potable water pressure boosting applications, and maintenance-free wet rotor technology that eliminates seals and couplings. It is also suitable for condenser and chilled water, as well as for use with VFD’s.
Wilo MVIS Pumps
sd
 
 
 
over35years
pumptollfree

Home | About Us | Service | Glossary | Line Card | Quotation | Contact Us | Sitemap | XMLSitemap

Copyright © 1978-2011 PumpSource, Inc. All Rights Reserved.